These procedures are valid for the versions of
software 3.xx (e.g. 3.04), it is enough to look at not the inspection door
on the eprom 27c512. In all the cases logical pcb it must be LGX23, can
imports the card HF.
You can recover the file of
the eprom in version 3.04 (last commercial version)
Try this for older
version like v1.02, adressing is different.
It is possible to program 15 channels on this type of Trx (Cs3-XXX, 160, 200, 450) without having recourse to an interface, the access to the menu of programming is done in the following way:
- power On the Trx (key)
- power Off and maintain the keysupported.
- enter the code on the digital keyboard : 84715033
you can try other code like 60609124, is useful for unlock firmware modified by users
- keys + / - allow to move in the menu of programming:- Enter a number of channel between 00 and 15, to enter the Tx frequency and Rx frequency.Two screens for the configuration of display of the infos.(you can modify the first) Finely which gives access the options of the software into hexadecimal (adresse/valor) Screen for channels Cloning Password, put here 1111... (it is simpler to find the code thereafter) End
- At the end of the programming, to press on the keyto return in normal mode.
It is possible to make a complete reset of the memory with loss
of the channels..... for that enter twice the code.
The station sends beeps, it is necessary to then to indicate the HF
card usez to the restart if not there is an error of synthetizer:
1 = 50Mhz
2 = VHF
3 = UHF
Some useful addresses (with your risks and dangers
to record the values before modifying them!)
|
|
|
|
|
With button = 10 Automatic = 18 (packet use on node) |
|
|
Yes = 10 Not = 00 |
|
|
Roger-Beep:
128 = not of Roger beep 64 = not of selective calling Example: No R.beep without call. sélect = 192 = c0 hexa No R.beep + call. sélect = 128 = 80 hexa |
|
|
Extremely = FD Faible = 00 |
|
|
|
|
|
|
|
|
The support on the postal and telecommunications authorities stops the scanning, the loss of ![]() |
|
|
|
|
|
|
|
|
|
(0)124
(0)12F (0)1Á (0)145 (0)150 (0)15B (0)166 (0)171 (0)17C (0)187 (0)192 (0)19D (0)1A8 (0)1B3 (0)1BE |
Channel 1
Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8 Channel 9 Channel 10 Channel 11 Channel 12 Channel 13 Channel 14 Channel 15 |
For each channel, with the address indicated:
Power Hf: 1 = 2,5w 2 = 5w 3 = 10w 4 = 25w 32 = Classification DTMF (defect CCIR) 64 = Channel in list scanning (see address 0116) Example, I want : that gives 4 + 32 + 64 = 100 = 64 in hexa |
At the time of the input of the hexadecimal values, it is sometimes
necessary to have letters:
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
|
|
|
|
|
|
The display in frontage consists of 16 characters, during the selection of the display of the frequency, the data overlap with channels (CC), the code of call (AAA) and relay (RR). It work but it is not very readable by moments! This said, the display of the frequency comprises some little bugs
- To pass in programming mode and to publish the
1st small display:
Original:
|
|
![]() |
|
|
|
|
|
|
|
|
![]() |
|
|
![]() |
||
New:
|
|
|
|
|
|
![]() |
![]() |
![]() |
|
|||||||
give:
|
|
|
|
|
|
|
|
|
|
|
![]() |
![]() |
![]() |
|
Correspondence of the keys:
|
|
![]() |
![]() |
|
|
![]() |
|
|
![]() |
|
|
![]() |
|
![]() |
![]() |
MMM : frequency (8 characters)
CC : number of channel
K : Function horn: witness put in communication (squelch)
: S-meter
: M/A of the loudspeaker
Opening an phone relay with
the 1750Hz tone
The station does not make it possible to send dial tones DTMF but CCIR...
on the other hand dial tone 8 of this standard corresponds to 1747Hz what
is largely sufficient.
In programming mode, to modify the following values:
The sending of the 1750Hz is carried out with the key(0)06D: 08 (value dial tone)(0)070: 64 (1750Hz duration = value hexa X 10ms, here 1s)